DMP Electronics XR500 Manual do Utilizador descarregar pdf (Página 65)

Digital Monitoring Products XR500 Series Canadian Programming Guide

zone informaTion

FA Series Wireless

For an FA Series Remote Wireless ReceiversettheHouseCodeto99.SeeHouseCodeprogrammingin

SystemOptions.Onlyzones500to699canbeprogrammedasFASeriesWirelesszonesformaximumof

200WirelessZones.

For a DMP 1100X Wireless Receiver see section 16.10.

19.12

ZONE INFORMATION

WIRELESS? NO YES

Wireless

SelectYEStoprogramawirelesszoneconnectedtoanFASeriesFA400-DMPRemote

WirelessReceiver.PresstheCOMMANDkeytocontinuewithwirelessprogramming.

19.12.1

CHECK IN TM: 60

Check-in Time

Youcansetwirelesstransmitterstocheckinautomaticallyevery10,30,or60

secondsornotatall.Tochangethe60seconddefault,pressanytoprowSelect

keytodisplayNONE103060.Selectthecheck-intimeyouwantforthiszone.

Note:RefertotheWirelessCheck-inandSupervisionTimeDenitionssectionof

the Appendix for supervision information.

19.12.2

INT CONT NO YES

Internal Contact

SelectYEStouseaninternalcontactonthewirelesstransmitter.SelectNO

touseanexternalcontact.WhenyouselectNO,thefollowingtwoprompts

display.

19.12.3

EOL NO YES

End-of-Line

Select YES to supervise an external contact connected to the wireless

transmitter.Atthecontact,installa2.2kOhmEnd-of-Lineresistorinparallel

forNormallyOpencontactsandinseriesforNormallyClosedcontacts.

19.12.4

NRM OPEN NO YES

Normally Open

SelectNOifthecontactconnectedtothewirelesstransmitterisNormally

Closed.

19.12.5

NEXT ZONE NO YES

Next Zone

SelectYEStoreturntotheZONENO:-prompttoprogramanewzone.Select

NOtodisplaytheAlarmActionoption.

19.13

ALARM ACTION . . . .

Alarm Action

ThisoptionallowsyoutochangeanyZoneTypestandarddenitions.WhentheZone

Typeisspecied,theAlarmActionforthatzoneisstoredinmemory.

IftheZoneTypeisBlank,Night,Day,Exit,Auxiliary1,orAuxiliary2itisa

non-24-hourzoneandtheAlarmActionprogramingbeginswithDisarmedOpen.

IftheZoneTypeisFire,Panic,Emergency,orSupervisoryitisa24-hourzonethatis

alwaysarmedandtheAlarmActionprogrammingbeginswithArmedOpen.

TheFireVerifyZoneTypefunctionsthesameasFireType,withthefollowing

exceptions:WhenaFireVerifyzoneinitiatesanalarm,thepanelperformsaSensor

Reset. If any Fire Verify zone initiates an alarm within 120 seconds after the

reset, an alarm is indicated. If an alarm is initiated after 120 seconds, the cycle is

repeated and a zone fault report is sent to the receiver.

DoNOTprogramFireVerifyZoneTypesforZoneRetard.

19.14

DISARMED OPEN

Disarmed Open

Denestheactiontakenbythepanelwhenthezoneisopenedwhiletheareais

disarmed.Therearethreeactionstodene:Reporttotransmit,RelayOutputto

activate,andRelayOutputaction.

YoumustalsomaketheseselectionsfortheDisarmedShort,ArmedOpen,andArmed

Shortzoneconditions.PressCOMMANDtocontinue.

1 2 ... 60 61 62 63 64 65 66 67 68 69 70 ... 83 84

Comentários a estes Manuais

Sem comentários

DMP Electronics XR500 Manual do Utilizador Página 65

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso DMP Electronics XR500